A polycarbazole film was electrodeposited on a stainless-steel wire from a solution of N,N-dimethylformamide/propylene carbonate (1:9 v/v) containing 0.10 M carbazole and 0.10 M tetrabutylammonium perchlorate. The obtained polycarbazole fiber was immersed into an ionic liquid (1-hydroxyethyl-3-methyl imidazolium bis[(trifluoromethyl)sulfonyl]imide) solution (in dimethylsulfoxide) for 30 min, followed by drying under an infrared lamp. The resulting polycarbazole/ionic liquid fiber was applied to the headspace solid-phase microextraction and determination of aromatic esters by coupling with gas chromatography and flame ionization detection. Under the optimized conditions, the limits of detection were below 61 ng/L (S/N = 3) and the linear ranges were 0.061−500 μg/L with correlation coefficients above 0.9876. The relative standard deviations were below 4.8% (n = 5) for a single fiber, and below 9.9% for multi-fiber (n = 4). This fiber also exhibited good stability. It could be used for more than 160 times of headspace solid-phase microextraction and could withstand a high temperature up to 350°C.

A novel polycarbazole coating was prepared by cyclic voltammetry on a platinum wire. The solution for electropolymerization contained N,N-dimethylformamide, propylene carbonate (v/v = 1:9), 0.10 M carbazole and 0.10 M tetrabutylammonium perchlorate; the cyclic scan potential range was 0.8–2.0 V (versus Ag/AgCl). The resulting polycarbazole coating showed a porous structure and had a large specific surface area. When it was used for the headspace solid-phase microextraction of chlorobenzenes (i.e. chlorobenzene, 2-chlorotoluene, 1,2-dichlorobenzene, 1,3-dichlorobenzene, 1,2,4-trichlorobenzene) followed by GC analysis, it presented excellent analytical performance. Under the optimized conditions the linear ranges were 0.25–250 μg/L with correlation coefficients >0.985, and the low detection limits were 15–61 ng/L (S/N = 3) for different chlorobenzenes. The RSDs were 2.4–4.9% for five successive measurements with a single fiber, and for fiber-to-fiber they were 6.3–13.1% (n = 5). Furthermore, the polycarbazole coating displayed good thermal stability (>350°C) and durability (more than 250 times). The proposed method was successfully applied to the extraction and determination of chlorobenzenes in waste water and lake water, and the recoveries for standards added were 86–114% for different analytes.

A headspace single-drop microextraction (SDME) based on ionic liquid (IL) has been developed for the gas chromatographic determination of phenols. The volume of IL microdrop used was 1 μL. After extraction, the analytes were desorbed from the drop in the injection port and the involatile IL was withdrawn into the microsyringe. To facilitate the withdrawal of IL the upper diameter of the split inlet liner was enlarged to some extent. Some parameters were optimized for the determination of phenols. Under the selected conditions, i.e., desorption for 100 s at 210°C after extraction for 25 min at 50°C in solutions (pH 3) containing 0.36 g/mL sodium chloride, the LODs, RSDs, and the average enrichment factors of phenols were 0.1–0.4 ng/mL, 3.6–9.5% (n = 5), and 35–794, respectively. The proposed procedure was applied to the determination of phenols in lake water and wastewater samples, and the spiked recoveries were in the range of 81–111% at a spiked level of 0.4 μg/mL. This method is a promising alternative for the sensitive determination of phenolic compounds.